Sensor Heads

Model			ZX-EDR5T	ZX-ED01T	ZX-ED02T / EM02T	ZX-EM07MT	ZX-EV04T	ZX-EM02HT
Measurement range			0 to 0.5 mm	0 to 1 mm	0 to 2 mm	0 to 7 mm	0 to 4 mm	0 to 2 mm
Sensing object			Magnetic metals (Measurement ranges and linearities are different for non-magnetic metals. Refer to Engineering Data on See Engineering Data (Typical).)
Standard reference object			18 × 18 × 3 mm		30 × 30 × 3 mm	60 × 60 × 3 mm		45 × 45 × 3 mm
			Material: ferrous (S50C)
Resolution *1			1 μm
Linearity *2			± 0.5% F.S.					± 1.0% F.S. *5
Linear output range			Same as measurement range.
Temperature characteristic *3 (including Amplifier Unit)			0.15 % F.S./°C	0.07% F.S./°C				0.1% F.S./°C
Ambient temper- ature	Operating *4		0 to 50°C (with no icing or con- densation)	-10 to 60°C (with no icing or condensation)				-10 to 200°C (with no icing or condensa- tion)
	Storage *4			-20 to 70°C (with no icing or condensation)
Ambient humidity			Operating and storage: 35% to 85% (with no condensation)
Insulation resistance			50 MΩ min. (at 500 DC)
Dielectric strength			1,000 VAC, 50/60 Hz for 1 min between charged parts and case
Vibration resistance (destruction)			10 to 55 Hz with 1.5-mm double amplitude for 2 h each in X, Y, and Z directions
Shock resistance (destruction)			500 m/s2, 3 times each in X, Y, and Z directions
Degree of protection (Sensor Head)			IEC60529, IP65	IEC60529, IP67				IEC60529, IP60 *6
Connection method			Connector relay (standard cable length: 2 m)
Weight (packed state)			Approx. 120 g	Approx. 140 g		Approx. 160 g	Approx. 130 g	Approx. 160 g
Materials	Sensor Head	Case	Brass	Stainless steel	Brass		Zinc (nickel- plated)	Brass
		Sensing surface	Heat-resistant ABS					PEEK
		Tightening nut	—		Brass (nickel-plated) (except ZX-ED02T)		—	Brass (nickel-plated)
		Toothed washer	—		Iron (zinc-plated) (except ZX-ED02T)		—	Iron (zinc-plated)
	Preamplifier		PES
Accessories			Amplifier Mounting Brackets (ZX-XBE1), Instruction Manual

1. Resolution: The resolution is the deviation (±3σ) in the linear output when connected to the ZX-EDA Amplifier Unit. The above values indicate the deviations observed 30 minutes after the power is turned ON. (The resolution is measured with OMRON’s standard reference object at 1/2 of the measurement range with the ZX-EDA set for the maximum average count of 4,096 per period.) The resolution is given at the repeat accuracy for a stationary workpiece, and is not an indication of the distance accuracy. The resolution may be adversely affected under strong electromagnetic fields.
2. Linearity: The linearity is given as the error in an ideal straight line displacement output when measuring the standard reference object. The linearity and measurement values vary with the object being measured.
3. Temperature characteristic: The temperature characteristic is measured with OMRON’s standard reference object at 1/2 of the measurement range.
4. The ambient temperature given is only for the sensor head. It is -10 to 60°C for the preamp.
5. The value given is for an ambient temperature of 25°C.
6. Do not use in moist environments because the case is not waterproof.

Amplifier Units

Model	ZX-EDA11	ZX-EDA41
Measurement period *1	150 μs
Possible average count settings	1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1,024, 2,048, or 4,096
Linear output *2	Current output: 4 to 20 mA/F.S., Max. load resistance: 300 Ω Voltage output: ± 4 V ( ± 5 V, 1 to 5 V *3), Output impedance: 100 Ω
Judgement outputs (3 outputs: HIGH/PASS/LOW)	NPN open-collector outputs, 30 VDC, 50 mA max. Residual voltage: 1.2 V max.	PNP open-collector outputs, 30 VDC, 50 mA max. Residual voltage: 2 V max.
Zero reset input, timing input, reset input, judgement output hold input	ON: Short-circuited with 0-V terminal or 1.5 V or less OFF: Open (leakage current: 0.1 mA max.)	ON: Supply voltage short-circuited or supply voltage within 1.5 V OFF: Open (leakage current: 0.1 mA max.)
Function	– Number of display digit changes – Sample hold – Peak hold – Bottom hold, peak-to-peak hold – Self-peak hold – Self-bottom hold – Average hold – Delay hold – Zero reset – Initial reset – Linearity initialization – ON-delay timer – OFF-delay timer – One-shot timer – Previous value comparison – Non-measurement setting – Direct threshold value setting – Position teaching – Automatic teaching – Hysteresis width setting – Timing inputs – Reset input – Judgement output hold input – Monitor focus – Linear output correction – (A-B) calculations *4 – (A+B) calculations *4 – K-(A+B) calculation *4 – Mutual interference prevention *4 – Sensor disconnection detection – Zero reset memory – Zero reset indicator – Key lock
Indications	Judgement indicators: High (orange), pass (green), low (yellow), 7-segment main digital display (red), 7-segment sub-digital display (yellow), power ON (green), zero reset (green), enable (green)
Voltage influence (including Sensor)	0.5% F.S. of linear output value at ±20% of power supply voltage
Power supply voltage	12 to 24 VDC ± 10%, Ripple (p-p): 10% max.
Current consumption	140 mA max. with power supply voltage of 24 VDC (with Sensor connected)
Ambient temperature	Operating and storage: 0 to 50°C (with no icing or condensation)
Ambient humidity	Operating and storage: 35% to 85% (with no condensation)
Insulation resistance	20 MΩ min. (at 500 DC)
Dielectric strength	1,000 VAC, 50/60 Hz for 1 min
Vibration resistance (destruction)	10 to 150 Hz with 0.7-mm double amplitude for 80 min each in X, Y, and Z directions
Shock resistance (destruction)	300 m/s2, 3 times each in 6 directions (up, down, left, right, forward, backward)
Connection method	Prewired (standard cable length: 2 m)
Weight (packed state)	Approx. 350 g
Materials	Case: PBT (polybutylene terephthalate), Cover: Polycarbonate
Accessories	Instruction Manual

1. The response time for the first linear output or judgment output is calculated as follows (with fixed sensitivity): Measurement period × (Average count setting + The response time for the second and later outputs is the measurement period specified in the table.
2. The output can be switched between a current output and voltage output using a switch on the bottom of the Amplifier Unit.
3. Setting is possible via the monitor focus function.
4. A Calculating Unit (ZX-CAL2) is required.

Sensors

Sensor Heads

ZX-EDR5T

ZX-ED01T

ZX-ED02T

ZX-EM02T

ZX-EM07MT

ZX-EV04T

ZX-EM02HT

Amplifier Units

ZX-EDA11
ZX-EDA41

Accessories (Sold Separately)

Preamplifier Mounting Bracket

ZX-XBE1

ZX-XBE2

Calculating Unit

ZX-CAL2

ZX-series Communications Interface Unit

ZX-SF11

Cables with Connectors on Both Ends (for Extension)

ZX-XC1A (1 m)
ZX-XC4A (4 m)
ZX-XC8A (8 m)

คุณสมบัติ | Photoelectric Displacement Sensor – ZX-E series

Photoelectric Displacement Sensor	ZX-E
ช่วงการวัด	0 – 0.5, 0 – 1, 0 – 2, 0 – 4, 0 – 7 mm
การตรวจจับวัตถุ	โลหะแม่เหล็ก
ความละเอียด	1 ไมโครเมตร
ความเที่ยงตรง	± 0.5% F.S.
ระดับการป้องกัน	IP60, IP65, IP67
วัสดุตัวเรือน	ทองเหลือง, สเตนเลส, สังกะสี (ชุบนิกเกิล)