OMRON Basic Switches – X

Specifications | Basic Switches – X

Ratings

Rated voltage	Non-inductive load (A)				Inductive load (A)
	Resistive load		Lamp load		Inductive load		Motor load
	NC	NO	NC	NO	NC	NO	NC	NO
8 VDC 14 VDC 30 VDC 125 VDC 250 VDC	10 10 10 10 3		3 3 3 3 1.5	1.5 1.5 1.5 1.5 0.75	10 10 10 7.5 2	10 10 10 6 1.5	5 5 5 5 2	2.5 2.5 2.5 2.5 1.5

Note:Note:
1. The above values are for the steady-state current.
2. Inductive load has a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC).
3. Lamp load has an inrush current of 10 times the steady-state current.
4. Motor load has an inrush current of 6 times the steady-state current.
5. The above electrical ratings also apply to the AC voltage.
6. With the reverse-type models (X-10GM[]), the normally closed circuits and normally open circuits are reversed.
7. The ratings values apply under the following test conditions:
(1) Ambient temperature: 20±2℃
(2) Ambient humidity: 65±5%RH
(3) Operating frequency: 20 operations/min

Contact Specification

Contacts	Material	Silver
	Gap (standard value)	0.9 mm
			Inrush current	NC	30 A max.
NO	15 A max.

Characteristics

Operating speed		0.1 mm to 1 m/s *1
Operating frequency	Mechanical	240 operations/min
	Electrical	20 operations/min
Insulation resistance		100 M Ω min. (at 500 VDC)
Contact resistance		15 m Ω max. (initial value)
Dielectric strength		1,500 VAC, 50/60 Hz for 1 min between terminals of the same polarity, between current-carrying metal parts and the ground, and between each terminal and non-current-carrying metal parts
			Vibration resistance	Malfunction	10 to 55 Hz, 1.5-mm double amplitude *2
			Shock resistance	Destruction	1,000 m/s2 max.
Malfunction	300 m/s2 max. *1 *2
Durability	Mechanical	1,000,000 operations min.
	Electrical	100,000 operations min.
Degree of protection		IP00
Degree of protection against electric shock		Class I
Proof tracking index (PTI)		175
Ambient operating temperature		− 25 ° C to 80 ° C (with no icing)
Ambient operating humidity		35% to 85%RH
Weight		Approx. 27 to 63 g

Note:*1. The values are for the pin plunger models. (Contact your OMRON representative for other models.)
*2. Malfunction: 1 ms max.

Dimensions | Basic Switches – X

Terminals

Screw Terminals (-B)

Solder Terminal (-A)

(“-A” is not included in the model numbers.)

Note: 1. Tighten the terminal screws to a torque of 0.78 to 1.18 Nm.
2. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
3. In case of DC voltage, set the COM to the positive terminal.

Mounting

Use M4 mounting screws with plane washers or spring washers to securely mount the Switch. Tighten the screws to a torque of 1.18 to 1.47 Nm.

The Switch can be panel mounted, provided that the hexagonal nut of the actuator is tightened to a torque of 2.94 to 4.9 Nm.

The models, illustrations, and graphics are for screw-terminal models. (The dimensions for models that are omitted here are the same as for pin-plunger models.)

Pin Plunger
X-10G-B

Slim Spring Plunger
X-10GS-B

Short Spring Plunger
X-10GD-B

Panel Mount Plunger
X-10GQ-B

Note: Do not use both the M12 mounting screw and the mounting holes in the case at the same time. Doing so will cause
stress to be applied to the Switch, possibly damaging the case or cover.

Panel Mount Roller Plunger
X-10GQ22-B

Note: Do not use both the M12 mounting screw and the mounting holes in the case at the same time. Doing so will cause
stress to be applied to the Switch, possibly damaging the case or cover.

Panel Mount Cross Roller Plunger
X-10GQ21-B

Note: Do not use both the M12 mounting screw and the mounting holes in the case at the same time. Doing so will cause
stress to be applied to the Switch, possibly damaging the case or cover.

Leaf Spring
X-10GL-B

Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.

* Be sure to use the switch at the rated OT value of 1.6 mm.

Short Hinge Lever
X-10GW21-B

Hinge Lever
X-10GW-B

Low-force Hinge Lever
X-10GW4-B

Short Hinge Roller Lever
X-10GW22-B

Hinge Roller Lever
X-10GW2-B

Reverse Hinge Lever
X-10GM-B

Reverse Short Hinge Lever
X-10GM22-B

Reverse Hinge Roller Lever
X-10GM2-B

Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.

Terminal Covers

AP-A

Soldering Terminal Use (Phenol Resin)

Note: The Cover has five thin, easy-to-separate portions for easy lead wire connections.

AP-B

Screw Terminal Use (Phenol Resin)

Note: The Cover has six thin, easy-to-separate portions for easy lead wire connections.

AP1-A

Soldering Terminal Use (Metal Press Mold)

Note: The Cover has five holes for easy lead wire connections.

AP1-B

Screw Terminal Use (Metal Press Mold)

Note: The Cover has six holes for easy lead wire connections.

AP-Z

Soldering or Screw Terminal Use (Vinyl Chloride)

Note: Each dimension has a tolerance of ±0.4 mm unless otherwise specified. (±0.8 mm for the AP-Z)

Separator

SEPARATOR FOR Z

Note: 1. Each dimension has a tolerance of ±0.4 mm unless otherwise specified.
2. The material is EAVTC (Epoxide Alkyd Varnished Tetron Cloth) and its heat-resisting temperature is 130°C.

Actuators

Hinge Lever
XAA-1

Hinge Roller Lever
ZAA-2

Short Panel Mount Plunger
ZAQ-3

Medium Panel Mount Plunger
ZAQ-2

Long Panel Mount Plunger
ZAQ-1

Panel Mount Roller Plunger
ZAQ-22

Note: Each dimension has a tolerance of ±0.4 mm unless otherwise specified.

Features | Basic Switches – X

Incorporates a small permanent magnet in the contact mechanism to deflect the arc to effectively extinguish it.

---

Properties | Basic Switches – X

Basic Switches	X
Rated voltage	8 – 250 VDC
Service life	1,000,000 times
Contact distance	0.9 mm (default)
Contact resistance	15 mΩ min (default)
Insulation resistance	100 MΩ min (500 VDC)
Weight (g)	Approx 27 – 63