OMRON Counter - H7GP
OMRON Counter – H7GP
Specifications | PLC – NX102 series
Electrical and Mechanical Specifications
| Item | Specification | |
|---|---|---|
| Model | NX102-[][][][] | |
| Enclosure | Mounted in a panel | |
| Dimensions (mm) *1 | 72 × 100 × 90 mm (W×H×D) | |
| Weight *2 | 390 g max. | |
| Unit power supply |
Power supply voltage | 24 VDC (20.4 to 28.8 VDC) |
| Unit power consumption *3 |
5.80 W max. | |
| Inrush current *4 | For cold start at room temperature: 10 A max./0.1 ms max. and 2.5 A max./150 ms max. |
|
| Current capacity of power supply terminal *5 |
4 A max. | |
| Isolation method | No isolation: between the Unit power supply terminal and internal circuit | |
| Power supply to the NX Unit power supply |
NX Unit power supply capacity |
10 W max. |
| NX Unit power supply efficiency |
80% | |
| Isolation method | No isolation: between the Unit power supply terminal and NX Unit power supply | |
| I/O Power Supply to NX Units | Not provided *6 | |
| External connection terminal |
Communication connector |
RJ45 for EtherNet/IP Communications × 2 RJ45 for EtherCAT Communications × 1 |
| Screwless clamping terminal block |
For Unit power supply input and grounding (Removable) | |
| Output terminal (service supply) |
Not provided | |
| RUN output terminal | Not provided | |
| NX bus connector | 32 NX Units can be connected | |
*1. Includes the End Cover, and does not include projecting parts.
*2. Includes the End Cover. The weight of the End Cover is 82 g.
*3. Includes an SD Memory Card. The NX Unit power consumption to NX Units is not included.
*4. The inrush current that occurs when the supplied power is changed to ON from a continuous OFF state.
The inrush current may vary depending on the operating condition and other conditions. Therefore, select fuses,
breakers, and external power supply devices that have enough margin in characteristic and capacity, considering
thecondition under which the devices are used.
In particular, in case when you insert a switch to turn ON/OFF the DC power supplied from an external power supply, if
the duration of an ON-OFF-ON cycle is one second or less, the inrush control circuit may not function, which cause an
inrush current of approximately 30 A/0.3 ms.
*5. The amount of current that can be passed constantly through the terminal. Do not exceed this current value when you
use a through-wiring for the Unit power supply.
*6. When the type of the I/O power supply to NX Units you use is the supply from NX bus, an Additional I/O Power Supply
Unit is required. Refer to NX-series NX102 CPU Unit Hardware User’s Manual (W593) for details.
General Specifications
| Item | Specification | |
|---|---|---|
| Enclosure | Mounted in a panel | |
| Grounding method | Ground to less than 100 Ω. | |
| Operating environment |
Ambient operating temperature |
0 to 55°C |
| Ambient operating humidity |
10% to 95% (with no condensation) | |
| Atmosphere | Must be free from corrosive gases. | |
| Ambient storage temperature |
-25 to 70°C (excluding battery) | |
| Altitude | 2,000 m max. | |
| Pollution degree | 2 or less: Meets IEC 61010-2-201. | |
| Noise immunity | 2 kV on power supply line (Conforms to IEC 61000-4-4.) | |
| Overvoltage category | Category II: Meets IEC 61010-2-201. | |
| EMC immunity level | Zone B | |
| Vibration resistance | Conforms to IEC 60068-2-6. 5 to 8.4 Hz with 3.5-mm amplitude, 8.4 to 150 Hz, acceleration of 9.8 m/s2 100 min each in X, Y, and Z directions (10 sweeps of 10 min each = 100 min total) |
|
| Shock resistance | Conforms to IEC 60068-2-27. 147 m/s2, 3 times in X, Y, and Z directions |
|
| Battery | Life | 5 years (Power ON time rate 0% (power OFF)) |
| Model | CJ1W-BAT01 (sold separately) | |
| Applicable standards *1 |
EU Directives | EN 61131-2 |
| cULus | Listed UL 61010-2-201 and ANSI/ISA 12.12.01 | |
| Shipbuilding Standards | NK, LR | |
| Other than the above. | RCM, KC, and EAC | |
*1. Refer to the consult your OMRON representative for the most recent applicable standards for each model.
Performance Specifications
| Item | NX102- | ||||||
|---|---|---|---|---|---|---|---|
| 12[][] | 11[][] | 10[][] | 90[][] | ||||
| Processing time |
Instruction execution times |
LD instruction | 3.3 ns | ||||
| Math instructions (for long real data) |
70 ns or more | ||||||
| Programming | Program capacity *1 |
Size | 5 MB | ||||
| Quantity | Number of POU definitions |
3,000 | |||||
| Number of POU instances |
9,000 | ||||||
| Memory capacity for variables *2 |
Retain attribute |
Size | 1.5 MB | ||||
| Number of variables |
10,000 | ||||||
| No Retain attribute |
Size | 32 MB | |||||
| Number of variables |
90,000 | ||||||
| Data types | Number of data types | 1,000 | |||||
| Memory for CJ-series Units (Can be specified with AT specifications for variables.) |
CIO Area | 0 to 6,144 words (CIO 0 to CIO 6,143) *3 |
|||||
| Work Area | 0 to 512 words (W0 to W511) *3 |
||||||
| Holding Area | 0 to 1,536 words (H0 to H1,535) *4 |
||||||
| DM Area | 0 to 32,768 words (D0 to D32,767) *4 |
||||||
| EM Area | 32,768 words × 25 banks (E0_0 to E18_32,767) *4 *5 |
||||||
| Motion control |
Number of controlled axes *6 |
Maximum number of controlled axes |
15 axes | 4 axes | |||
| Motion control axes |
11 axes | — | |||||
| Single-axis position control axes |
4 axes | ||||||
| Maximum number of used real axes |
12 axes | 8 axes | 6 axes | 4 axes | |||
| Used motion control servo axes |
8 axes | 4 axes | 2 axes | — | |||
| Used single- axis position control servo axes |
4 axes | ||||||
| Maximum number of axes for linear interpolation axis control |
4 axes per axes group | — | |||||
| Number of axes for circular interpolation axis control |
2 axes per axes group | — | |||||
| Maximum number of axes groups | 8 axes groups | — | |||||
| Motion control period | The same control period as that is used for the process data communications cycle for EtherCAT. |
||||||
| Cams | Number of cam data points |
Maximum points per cam table |
65,535 points | ||||
| Maximum points for all cam tables |
262,140 points | ||||||
| Maximum number of cam tables |
160 tables | ||||||
| Position units | Pulse, mm, μm, nm, degree, and inch | ||||||
| Override factors | 0.00%, or 0.01% to 500.00% | ||||||
| Built-in EtherNet/IP port |
Number of ports | 2 | |||||
| Physical layer | 10BASE-T/100BASE-TX | ||||||
| Frame length | 1,514 bytes max. | ||||||
| Media access method | CSMA/CD | ||||||
| Modulation | Baseband | ||||||
| Topology | Star | ||||||
| Baud rate | 100 Mbps (100BASE-TX) | ||||||
| Transmission media | STP (shielded, twisted-pair) cable of Ethernet category 5, 5e or higher |
||||||
| Maximum transmission distance between Ethernet switch and node |
100 m | ||||||
| Maximum number of cascade connections | There are no restrictions if an Ethernet switch is used. | ||||||
| CIP service: Tag data links (cyclic com- munications) |
Maximum number of connections |
32 per port 64 total |
|||||
| Packet interval *7 | Can be set for each connection. 1 to 10,000 ms in 1-ms increments |
||||||
| Permissible communications band |
12,000 pps *8 *9 (including heartbeat, CIP Safety routing) |
||||||
| Maximum number of tag sets | 32 per port 40 total *10 |
||||||
| Tag types | Network variables CIO/WR/HR/DM |
||||||
| Number of tags per connection (i.e., per tag set) |
8 (7 tags if Controller status is included in the tag set.) | ||||||
| Maximum number of tags | 256 per port 512 total |
||||||
| Maximum link data size per node (total size for all tags) |
19,200 bytes per port 38,400 bytes total |
||||||
| Maximum data size per connection |
600 bytes | ||||||
| Maximum number of registrable tag sets |
32 per port 40 total *10 (1 connection = 1 tag set) |
||||||
| Maximum tag set size | 600 bytes (Two bytes are used if Controller status is included in the tag set.) |
||||||
| Multi-cast packet filter *11 | Supported. | ||||||
| CIP message service: Explicit messages |
Class 3 (number of connections) |
32 per port 64 total (clients plus server) |
|||||
| UCMM (non- connection type) |
Maximum number of clients that can communicate at one time |
32 per port 64 total |
|||||
| Maximum number of servers that can communicate at one time |
32 per port 64 total |
||||||
| CIP Safety routing |
Maximum number of routable CIP Safety connections |
16 total | |||||
| Maximum routable safety data length per connection |
32 bytes | ||||||
| Number of TCP sockets | 60 | ||||||
| OPC UA Server |
Support profile/Model | UA 1.02 Micro Embedded Device Server Profile PLCOpen Information Model |
|||||
| Default Endpoint/Port | opc.tcp://192.168.250.1:4840/ | ||||||
| Maximum number of sessions (Client) |
5 | ||||||
| Maximum number of Monitored Items per server |
2,000 | ||||||
| Sampling rate of Monitored Items (ms) |
0, 50, 100, 250, 500, 1000, 2000, 5,000, 10,000 (If set to 0 (zero), it is assumed that is set to 50.) |
||||||
| Maximum number of Subscriptions per server |
100 | ||||||
| Maximum number of variables that can be published |
10,000 | ||||||
| Maximum number of value attributes that can be published *16 |
10,000 | ||||||
| Maximum number of structure definitions that can be published |
100 | ||||||
| Restrictions on variables unable to be published |
• Variables whose size is over 1,024 bytes • Two-dimensional or higher structure arrays • Structures that include two-dimensional and higher arrays • Structures with four or higher levels of nesting • Unions • Arrays whose index number suffix does no start from 0 • Arrays with 1,024 or more elements • Structures with 100 or more members |
||||||
| SecurityPolicy/Mode | Select one of the following. None Sign – Basic128Rsa15 Sign – Basic256 Sign – Basic256Sha256 SignAndEncrypt – Basic128Rsa15 SignAndEncrypt – Basic256 SignAndEncrypt – Basic256Sha256 |
||||||
| Application Authentica- tion |
Authentication | X.509 | |||||
| Maximum number of storable certifications |
Trusted certification: 32 Issuer certification: 32 Rejected certification: 32 |
||||||
| User Authentica- tion |
Authentication | You can set the following items. User name/password Anonymous |
|||||
| Built-in EtherCAT port |
Communications standard | IEC 61158 Type12 | |||||
| EtherCAT master specifications | Class B (Feature Pack Motion Control compliant) | ||||||
| Physical layer | 100BASE-TX | ||||||
| Modulation | Baseband | ||||||
| Baud rate | 100 Mbps (100BASE-TX) | ||||||
| Duplex mode | Auto | ||||||
| Topology | Line, daisy chain, branching and ring *13 | ||||||
| Transmission media | Twisted-pair cable of category 5 or higher (double- shielded straight cable with aluminum tape and braiding) |
||||||
| Maximum transmission distance between nodes |
100 m | ||||||
| Maximum number of slaves | 64 | ||||||
| Range of node addresses that can be set | 1 to 192 | ||||||
| Maximum process data size | Input: 5,736 bytes Output: 5,736 bytes *14 |
||||||
| Maximum process data size per slave | Input: 1,434 bytes Output: 1,434 bytes |
||||||
| Communications cycle | 1,000 to 32,000 μs (in 250-μs increments) | ||||||
| Sync jitter | 1 μs max. | ||||||
| Unit configuration |
Units on CPU Rack |
Maximum number of NX Units that can be mounted to the CPU Unit |
32 | ||||
| Maximum I/O data size that can be allocated in the CPU Unit |
Inputs: 8,192 bytes *15 Outputs: 8,192 bytes *15 |
||||||
| Maximum number of NX Units for entire controller |
400 | ||||||
| Power supply | Model | A non-isolated power supply for DC input is built into the CPU Unit. |
|||||
| Power OFF detection time | 2 to 8 ms | ||||||
| Internal clock |
Accuracy | At ambient temperature of 55°C: -3.5 to 0.5 min error per month At ambient temperature of 25°C: -1.5 to 1.5 min error per month At ambient temperature of 0°C: -3 to 1 min error per month |
|||||
| Retention time of built-in capacitor | At ambient temperature of 40°C: 10 days | ||||||
*1. Execution objects and variable tables (including variable names)
*2. Memory used for CJ-series Units is included.
*3. The value can be set in 1-word increments. The value is included in the total size of variables without a Retain
attribute.
*4. The value can be set in 1-word increments. The value is included in the total size of variables with a Retain attribute.
*5. It is not possible to use the maximum number of words simultaneously for all banks, because the memory capacity for
variables with a Retain attribute is limited to 1.5 MB.
*6. For terminology, refer to the NJ/NX-series CPU Unit Motion Control User’s Manual (Cat. No. W507).
*7. Data will be refreshed at the set interval, regardless of the number of nodes.
*8. “pps” means packets per second, i.e., the number of communications packets that can be sent or received in one
second.
*9. The allowable bandwidth varies depending on the RPI of the connection in use, the primary task period, and the
number of ports simultaneously used for EtherNet/IP communications.
*10.When tag sets that exceed the total of 40 are set, a Number of Tag Sets for Tag Data Links Exceeded (840E0000 hex)
occurs.
*11.As the EtherNet/IP port implements the IGMP client, unnecessary multi-cast packets can be filtered by using an
Ethernet switch that supports IGMP Snooping.
*12.The number of value attributes is defined by the following formula.
Number of value attributes = (Number of basic data type variables) + (Number of array-specified elements) + (Number
of values in the structure)
*13.Ring topology is supported with the project version 1.40 or later of NX102-[][]00.
Slaves on a ring topology should support a ring topology. If Omron slaves, please see the user’s manual of slaves.
*14.For project unit version earlier than 1.40, the data must be within four frames.
*15.You can check the I/O allocation status with the Sysmac Studio. Refer to the NJ/NX-series CPU Unit Software User’s
Manual (Cat. No. W501) for how to check the I/O allocation status. Also, refer to the relevant manuals for specific
Units for the maximum I/O data size per NX Unit.
Function Specifications
| Item | NX102 | |||
|---|---|---|---|---|
| Tasks | Function | I/O refreshing and the user program are executed in units that are called tasks. Tasks are used to specify execution conditions and execution priority. |
||
| Periodically executed tasks |
Maximum number of primary periodic tasks |
1 | ||
| Maximum number of periodic tasks |
2 | |||
| Conditionally executed tasks |
Maximum number of event tasks |
32 | ||
| Execution condition | When Activate Event Task instruction is executed or when condition expression for variable is met |
|||
| Programming | POU (Program Organization Unit) |
Programs | POUs that are assigned to tasks | |
| Function blocks | POUs that are used to create objects with specific conditions |
|||
| Functions | POUs that are used to create objects that determine unique outputs for the inputs, such as for data processing |
|||
| Programming languages |
Types | Ladder diagrams *1 and structured text (ST) | ||
| Namespaces | A concept that is used to group identifiers for POU definitions |
|||
| Variables | External access of variables |
Network variables | The function which allows access from the HMI, host computers, or other controllers |
|
| Data types | Basic data types |
Boolean | BOOL | |
| Bit strings | BYTE, WORD, DWORD, LWORD | |||
| Integers | INT, SINT, DINT, LINT, UINT, USINT, UDINT, ULINT |
|||
| Real numbers | REAL, LREAL | |||
| Durations | TIME | |||
| Dates | DATE | |||
| Times of day | TIME_OF_DAY | |||
| Date and time | DATE_AND_TIME | |||
| Text strings | STRING | |||
| Derivative data types | Structures, unions, enumerations | |||
| Structures | Function | A derivative data type that groups together data with different variable types |
||
| Maximum number of members |
2,048 | |||
| Nesting maximum levels |
8 | |||
| Member data types | Basic data types, structures, unions, enumerations, array variables |
|||
| Specifying member offsets |
You can use member offsets to place structure members at any memory locations |
|||
| Unions | Function | A derivative data type that enables access to the same data with different data types |
||
| Maximum number of members |
4 | |||
| Member data types | BOOL, BYTE, WORD, DWORD, LWORD | |||
| Enumerations | Function | A derivative data type that uses text strings called enumerators to express variable values |
||
| Data type attributes |
Array specifications |
Function | An array is a group of elements with the same data type. You specify the number (subscript) of the element from the first element to specify the element |
|
| Maximum number of dimensions |
3 | |||
| Maximum number of elements |
65,535 | |||
| Array specifications for FB instances |
Supported | |||
| Range specifications | You can specify a range for a data type in advance. The data type can take only values that are in the specified range |
|||
| Libraries | User libraries | |||
| Motion control |
Control modes | Position control, velocity control, torque control |
||
| Axis types | Servo axes, virtual servo axes, encoder axes, virtual encoder axes, PTP axes |
|||
| Positions that can be managed | Command positions and actual positions | |||
| Single axes | Single-axis position control |
Absolute positioning | Positioning is performed for a target position that is specified with an absolute value |
|
| Relative positioning | Positioning is performed for a specified travel distance from the command current position |
|||
| Interrupt feeding | Positioning is performed for a specified travel distance from the position where an interrupt input was received from an external input |
|||
| Cyclic synchronous absolute positioning |
A positioning command is output each control period in Position Control Mode |
|||
| Single-axis velocity control |
Velocity control | Velocity control is performed in Position Control Mode |
||
| Cyclic synchronous velocity control |
A velocity command is output each control period in Velocity Control Mode |
|||
| Single-axis torque control |
Torque control | The torque of the motor is controlled | ||
| Single-axis synchronized control |
Starting cam operation |
A cam motion is performed using the specified cam table |
||
| Ending cam operation |
The cam motion for the axis that is specified with the input parameter is ended |
|||
| Starting gear operation |
A gear motion with the specified gear ratio is performed between a master axis and slave axis |
|||
| Positioning gear operation |
A gear motion with the specified gear ratio and sync position is performed between a master axis and slave axis |
|||
| Ending gear operation | The specified gear motion or positioning gear motion is ended |
|||
| Synchronous positioning |
Positioning is performed in sync with a specified master axis |
|||
| Master axis phase shift |
The phase of a master axis in synchronized control is shifted |
|||
| Combining axes | The command positions of two axes are added or subtracted and the result is output as the command position |
|||
| Single-axis manual operation |
Powering the Servo | The Servo in the Servo Drive is turned ON to enable axis motion |
||
| Jogging | An axis is jogged at a specified target velocity |
|||
| Auxiliary functions for single-axis control |
Resetting axis errors |
Axes errors are cleared | ||
| Homing | A motor is operated and the limit signals, home proximity signal, and home signal are used to define home |
|||
| Homing with parameter |
The parameters are specified, the motor is operated, and the limit signals, home proximity signal, and home signal are used to define home |
|||
| High-speed homing | Positioning is performed for an absolute target position of 0 to return to home |
|||
| Stopping | An axis is decelerated to a stop | |||
| Immediately stopping | An axis is stopped immediately | |||
| Setting override factors |
The target velocity of an axis can be changed | |||
| Changing the current position |
The command current position or actual current position of an axis can be changed to any position. |
|||
| Enabling external latches |
The position of an axis is recorded when a trigger occurs |
|||
| Disabling external latches |
The current latch is disabled | |||
| Zone monitoring | You can monitor the command position or actual position of an axis to see when it is within a specified range (zone) |
|||
| Enabling digital cam switches |
You can turn a digital output ON and OFF according to the position of an axis |
|||
| Monitoring axis following error |
You can monitor whether the difference between the command positions or actual positions of two specified axes exceeds a threshold value |
|||
| Resetting the following error |
The error between the command current position and actual current position is set to 0 |
|||
| Torque limit | The torque control function of the Servo Drive can be enabled or disabled and the torque limits can be set to control the output torque |
|||
| Command position compensation |
The function which compensates the position for the axis in operation |
|||
| Cam monitor | Outputs the specified offset position for the slave axis in synchronous control. |
|||
| Start velocity | You can set the initial velocity when axis motion starts |
|||
| Axes groups | Multi-axes coordinated control |
Absolute linear interpolation |
Linear interpolation is performed to a specified absolute position |
|
| Relative linear interpolation |
Linear interpolation is performed to a specified relative position |
|||
| Circular 2D interpolation |
Circular interpolation is performed for two axes |
|||
| Axes group cyclic synchronous absolute positioning |
A positioning command is output each control period in Position Control Mode |
|||
| Auxiliary functions for multi-axes coordinated control |
Resetting axes group errors |
Axes group errors and axis errors are cleared |
||
| Enabling axes groups | Motion of an axes group is enabled | |||
| Disabling axes groups |
Motion of an axes group is disabled | |||
| Stopping axes groups |
All axes in interpolated motion are decelerated to a stop |
|||
| Immediately stopping axes groups |
All axes in interpolated motion are stopped immediately |
|||
| Setting axes group override factors |
The blended target velocity is changed during interpolated motion |
|||
| Reading axes group positions |
The command current positions and actual current positions of an axes group can be read |
|||
| Changing the axes in an axes group |
The Composition Axes parameter in the axes group parameters can be overwritten temporarily |
|||
| Common items |
Cams | Setting cam table properties |
The end point index of the cam table that is specified in the input parameter is changed |
|
| Saving cam tables | The cam table that is specified with the input parameter is saved in non-volatile memory in the CPU Unit |
|||
| Generating cam tables |
The cam table is generated from the cam property and cam node that is specified in input parameters |
|||
| Parameters | Writing MC settings | Some of the axis parameters or axes group parameters are overwritten temporarily |
||
| Changing axis parameters |
The axis parameters can be accessed or changed from the user program |
|||
| Auxiliary functions |
Count modes | You can select either Linear Mode (finite length) or Rotary Mode (infinite length). |
||
| Unit conversions | You can set the display unit for each axis according to the machine |
|||
| Acceleration/ deceleration control |
Automatic acceleration/ deceleration control |
Jerk is set for the acceleration/deceleration curve for an axis motion or axes group motion |
||
| Changing the acceleration and deceleration rates |
You can change the acceleration or deceleration rate even during acceleration or deceleration |
|||
| In-position check | You can set an in-position range and in- position check time to confirm when positioning is completed |
|||
| Stop method | You can set the stop method to the immediate stop input signal or limit input signal |
|||
| Re-execution of motion control instructions |
You can change the input variables for a motion control instruction during execution and execute the instruction again to change the target values during operation |
|||
| Multi-execution of motion control instructions (Buffer Mode) |
You can specify when to start execution and how to connect the velocities between operations when another motion control instruction is executed during operation |
|||
| Continuous axes group motions (Transition Mode) |
You can specify the Transition Mode for multi-execution of instructions for axes group operation |
|||
| Monitoring functions |
Software limits | The movement range of an axis is monitored | ||
| Following error | The error between the command current value and the actual current value is monitored for each axis |
|||
| Velocity, acceleration rate, deceleration rate, torque, interpolation velocity, interpolation acceleration rate, interpolation deceleration rate |
You can set and monitor warning values for each axis and each axes group |
|||
| Absolute encoder support | You can use an OMRON 1S-series Servomotor or G5-series Servomotor with an Absolute Encoder to eliminate the need to perform homing at startup |
|||
| Input signal logic inversion | You can inverse the logic of immediate stop input signal, positive limit input signal, negative limit input signal, or home proximity input signal |
|||
| External interface signals | The Servo Drive input signals listed below are used. Home signal, home proximity signal, positive limit signal, negative limit signal, immediate stop signal, interrupt input signal |
|||
| Unit (I/O) management |
EtherCAT slaves |
Maximum number of slaves | 64 | |
| Communi- cations |
Built-in EtherNet/IP port |
Communications protocol | TCP/IP, UDP/IP | |
| TCP/IP functions |
CIDR | The function which performs IP address allocations without using a class (class A to C) of IP address |
||
| IP Forwarding | The function which forwards IP packets between interfaces |
|||
| Packet Filter | The function which checks the IP packet to determine whether to receive and send it based on the source IP address and TCP port number |
|||
| CIP communica- tions service |
Tag data links | Programless cyclic data exchange is performed with the devices on the EtherNet/IP network |
||
| Message communications |
CIP commands are sent to or received from the devices on the EtherNet/IP network |
|||
| CIP Safety routing | Routing function for CIP Safety on the EtherNet/IP network. The endpoint of CIP Safety is NX-SL5[]00 in the system |
|||
| TCP/IP applications |
Socket services | Data is sent to and received from any node on Ethernet using the UDP or TCP protocol. Socket communications instructions are used |
||
| FTP client | Files are transferred via FTP from the CPU Unit to computers or controllers at other Ethernet nodes. FTP client communications instructions are used |
|||
| FTP server | Files can be read from or written to the SD Memory Card in the CPU Unit from computers at other Ethernet nodes |
|||
| Automatic clock adjustment |
Clock information is read from the NTP server at the specified time or at a specified interval after the power supply to the CPU Unit is turned ON. The internal clock time in the CPU Unit is updated with the read time |
|||
| SNMP agent | Built-in EtherNet/IP port internal status information is provided to network management software that uses an SNMP manager |
|||
| OPC UA | Server function | The function to respond to requests from clients on the OPC UA network |
||
| EtherCAT port |
Supported services |
Process data communications |
A communications method to exchange control information in cyclic communications between the EtherCAT master and slaves. This communications method is defined by CoE |
|
| SDO communications |
A communications method to exchange control information in noncyclic event communications between EtherCAT master and slaves. This communications method is defined by CoE |
|||
| Network scanning | Information is read from connected slave devices and the slave configuration is automatically generated |
|||
| DC (Distributed Clock) | Time is synchronized by sharing the EtherCAT system time among all EtherCAT devices (including the master) |
|||
| Enable/disable settings for slaves | The slaves can be enabled or disabled as communications targets |
|||
| Disconnecting/connecting slaves | Temporarily disconnects a slave from the EtherCAT network for maintenance, such as for replacement of the slave, and then connects the slave again |
|||
| Supported application protocol |
CoE | SDO messages of the CAN application can be sent to slaves via EtherCAT |
||
| Communications instructions | CIP communications instructions, socket communications instructions, SDO message instructions, no-protocol communications instructions, FTP client instructions, Modbus RTU protcol instructions, Modbus TCP protcol instructions |
|||
| System management |
Event logs | Function | Events are recorded in the logs | |
| Maximum number of events |
System event log | 768 *2 [containing] • For CPU Unit: 512 • For NX Unit without MPU: 256 |
||
| Access event log | 576 [containing] • For CPU Unit: 512 • For NX Unit without MPU: 64 |
|||
| User-defined event log |
512 | |||
| Debugging | Online editing |
Single | Programs, function blocks, functions, and global variables can be changed online. More than one operators can change POUs individually via network |
|
| Forced refreshing | The user can force specific variables to TRUE or FALSE |
|||
| Maximum number of forced variables |
Device variables for EtherCAT slaves |
64 | ||
| MC Test Run | Motor operation and wiring can be checked from the Sysmac Studio |
|||
| Synchronizing | The project file in the Sysmac Studio and the data in the CPU Unit can be made the same when online |
|||
| Differential monitoring | You can monitor when a variable changes to TRUE or changes to FALSE |
|||
| Maximum number of monitored variables |
8 | |||
| Data tracing | Types | Single triggered trace |
When the trigger condition is met, the specified number of samples are taken and then tracing stops automatically |
|
| Continuous trace | Data tracing is executed continuously and the trace data is collected by the Sysmac Studio |
|||
| Maximum number of simultaneous data traces |
2 | |||
| Maximum number of records | 10,000 | |||
| Sampling | Maximum number of sampled variables |
48 | ||
| Timing of sampling | Sampling is performed for the specified task period, at the specified time, or when a sampling instruction is executed |
|||
| Triggered traces | Trigger conditions are set to record data before and after an event |
|||
| Trigger conditions | • When BOOL variable changes to TRUE or FALSE • Comparison of non-BOOL variable with a constant. Comparison method: Equals (=), Greater than (>), Greater than or equals (≥), Less than (<), Less than or equals (≤), Not equal (≠) |
|||
| Delay | You can set the percentage of sampling before and after the trigger condition is met |
|||
| Safety data logging |
Function | Records variables used in the safety program of the Safety CPU Unit in a chronological order |
||
| Targets | Target Safety CPU Unit |
NX-SL5[]00 *3 | ||
| Target variable types | Exposed variables and device variables used in the safety program |
|||
| Maximum number of logged variables |
100 | |||
| Data types | SAFEBOOL, SAFEBYTE, SAFEWORD, SAFEINT, SAFEDINT,BOOL, BYTE, WORD, INT, DINT |
|||
| Maximum logging time |
480 s (Depends on logging interval) | |||
| Logging interval | Select from minimum value which stores from primary periodic task cycle or adds constant number multiple (x1, x2, x3, x4) of primary periodic task cycle *4 |
|||
| Maximum number of simultaneous executions |
2 | |||
| Simulation | The operation of the CPU Unit is emulated in the Sysmac Studio |
|||
| Reliability functions |
Self- diagnosis |
Controller errors |
Levels | Major faults, partial faults, minor faults, observation, information |
| User-defined errors | User-defined errors are registered in advance and then records are created by executing instructions |
|||
| Levels | 8 | |||
| Security | Protecting software assets and preventing operating mistakes |
CPU Unit names and serial IDs | When going online to a CPU Unit from the Sysmac Studio, the CPU Unit name in the project is compared to the name of the CPU Unit being connected to |
|
| Protection | User program transfer with no restoration information |
You can prevent reading data in the CPU Unit from the Sysmac Studio |
||
| CPU Unit write protection |
You can prevent writing data to the CPU Unit from the Sysmac Studio or SD Memory Card |
|||
| Overall project file protection |
You can use passwords to protect .smc files from unauthorized opening on the Sysmac Studio |
|||
| Data protection | You can use passwords to protect POUs on the Sysmac Studio |
|||
| Verification of operation authority | Online operations can be restricted by operation rights to prevent damage to equipment or injuries that may be caused by operating mistakes |
|||
| Number of groups | 5 | |||
| Verification of user program execution ID |
The user program cannot be executed without entering a user program execution ID from the Sysmac Studio for the specific hardware (CPU Unit) |
|||
| SD Memory Card functions |
Storage type | SD Memory Card, SDHC Memory Card | ||
| Application | Automatic transfer from SD Memory Card |
When the power supply to the controller is turned ON, the data that is stored in the autoload directory of the SD Memory Card is transferred to the controller |
||
| Program transfer from SD Memory Card |
With the specification of the system-defined variable, you can transfer a program that is stored in the SD Memory Card to the controller |
|||
| SD Memory Card operation instructions |
You can access SD Memory Cards from instructions in the user program |
|||
| File operations from the Sysmac Studio |
You can perform file operations for controller files in the SD Memory Card and read/write standard document files on the computer |
|||
| SD Memory Card life expiration detection |
Notification of the expiration of the life of the SD Memory Card is provided in a system- defined variable and event log |
|||
| Backing up data |
SD Memory Card backups |
Operating methods |
CPU Unit front- panel DIP switch |
You can perform backup, verification, and restoration operations by manipulating the front-panel DIP switch on the CPU Unit |
| Specification with system-defined variables |
You can perform backup, verification, and restoration operations by manipulating system-defined variables |
|||
| SD Memory Card Window in Sysmac Studio |
Backup and verification operations are performed from the SD Memory Card Window of the Sysmac Studio |
|||
| Special instruction | The special instruction is used to backup data |
|||
| Protection | Disabling backups to SD Memory Cards |
Backing up data to a SD Memory Card is prohibited |
||
| Safety Unit Restore from SD Memory Card | Restores the data of the Safety CPU Unit using the front-panel DIP switch on the Safety CPU Unit and SD Memory Card |
|||
| Sysmac Studio Controller backups | The Sysmac Studio is used to backup, restore, or verify controller data |
|||
*1. Inline ST is supported. (Inline ST is ST that is written as an element in a ladder diagram.)
*2. Up to 512 system logs for events in the CPU Unit and 256 system logs in the NX Unit can be recorded.
*3. When connected to a CPU rack.
*4. Minimum value fulfills all these conditions.
• Larger than 5 ms
• Constant number multiple of primary periodic task cycle
Function Specifications of the Database Connection CPU Units
Besides functions of the NX102-[][][][], functions supported by the NX102-[][]20 are as follows.
| Item | Description | |||||
|---|---|---|---|---|---|---|
| NX102-1220 | NX102-1120 | NX102-1020 | NX102-9020 | |||
| Supported port | Built-in EtherNet/IP port | |||||
| Supported DB versions *1 *2 |
SQL Server by Microsoft | 2012/2014/2016/2017 | ||||
| Oracle Database by Oracle | 11g/12c/18c | |||||
| DB2 for Linux, UNIX and Windows by IBM |
9.7/10.1/10.5/11.1 | |||||
| MySQL Community Edition by Oracle*3 |
5.6/5.7/8.0 | |||||
| Firebird by Firebird Foundation |
2.5 | |||||
| PostgreSQL by PostgreSQL Global Development Group |
9.4/9.5/9.6/10 | |||||
| Number of DB Connections (Number of databases that can be connected at the same time) |
2*4 *5 | |||||
| Instruction | Supported operations | The following operations can be performed by executing DB Connection Instructions in the CPU Units: Inserting records (INSERT), Updating records (UPDATE), Retrieving records (SELECT), Deleting records (DELETE), Execute Stored Procedure*6, and Execute Batch Insert*6 |
||||
| Max. number of instructions for simultaneous execution |
32 | |||||
| Max. number of columns in an INSERT operation |
SQL Server: 1,024 Oracle: 1,000 DB2: 1,000 MySQL: 1,000 Firebird: 1,000 PostgreSQL: 1,000 |
|||||
| Max. number of columns in an UPDATE operation |
SQL Server: 1,024 Oracle: 1,000 DB2: 1,000 MySQL: 1,000 Firebird: 1,000 PostgreSQL: 1,000 |
|||||
| Max. number of columns in a SELECT operation |
SQL Server: 1,024 Oracle: 1,000 DB2: 1,000 MySQL: 1,000 Firebird: 1,000 PostgreSQL: 1,000 |
|||||
| Max. number of records in the output of a SELECT operation |
65,535 elements, 4 MB | |||||
| Stored procedure call *6 |
Supported databases |
• SQL Server • Oracle Database • MySQL Community Edition • PostgreSQL |
||||
| Argument (Sum of IN, OUT and INOUT) |
Up to 256 variables*7 | |||||
| Return value | One variable | |||||
| Result set | Supported | |||||
| Spool function | Not supported | |||||
| Batch insert execution *6 |
Supported databases |
• SQL Server • Oracle Database • MySQL Community Edition • PostgreSQL |
||||
| Supported data size |
Less than 1,000 columns and upper limit (8 MB) of structure variable size or less*8 |
|||||
| Spool function | Not supported | |||||
| Max. number of DB Map Variables for which a mapping can be connected *9 |
SQL Server: 30*10 Oracle: 20*10 DB2: 20*10 MySQL: 20*10 Firebird: 15 PostgreSQL: 20*10 |
|||||
| Run mode of the DB Connection Service | Operation Mode or Test Mode • Operation Mode: When each instruction is executed, the service actually accesses the DB • Test Mode: When each instruction is executed, the service ends the instruction normally without accessing the DB actually |
|||||
| Spool function | Used to store SQL statements when an error occurred and resend the statements when the communications are recovered from the error |
|||||
| Spool capacity*11 | 192 KB | |||||
| Operation Log function | The following three types of logs can be recorded: • Execution Log: Log for tracing the executions of the DB Connection Service • Debug Log: Detailed log for SQL statement executions of the DB Connection Service • SQL Execution Failure Log: Log for execution failures of SQL statements in the DB |
|||||
| DB Connection Service Shutdown function |
Used to shut down the DB Connection Service after automatically saving the operation log files into the SD Memory Card |
|||||
| Encrypted Communi- cation |
Supported databases | • SQL Server • Oracle Database • MySQL Community Edition • PostgreSQL |
||||
| TLS Ver. | TLS 1.2 | |||||
*1. SQL Server 2014, Oracle Database 12c and PostgreSQL 9.4 are supported by the DB Connection Service Version 1.02
or higher.
SQL Server 2016, MySQL 5.7, DB2 11.1 and PostgreSQL 9.5/9.6 are supported by the DB Connection Service Version
1.03 or higher.
SQL Server 2017 is supported by the DB Connection Service Version 1.04 or higher.
Oracle Database 18c, MySQL Community Edition 8.0 and PostgreSQL 10 are supported by the DB Connection Service
Version 2.00 or higher.
You cannot use Oracle 10g with the DB Connection Service version 2.00 or higher.
*2. Connection to the DB on the cloud is not supported.
*3. The supported storage engines of the DB are InnoDB and MyISAM.
*4. When two or more DB Connections are established, the operation cannot be guaranteed if you set different database
types for the connections.
*5. For the DB Connection Service Version lower than 1.04, Number of DB Connection is 1.
*6. The function is available for the DB Connection Service Version 2.00 or higher.
*7. Depends on members of a structure.
*8. Constrained by the memory capacity for variables. See the specifications for the memory capacity for variables.
*9. Even if the number of DB Map Variables has not reached the upper limit, the maximum total number of members of
structures used as data type of DB Map Variables is 10,000.
*10.For DB Connection Service Version lower than 1.04, Max. number of DB Map Variables for which a mapping can be
connected is 15.
*11.Refer to the NJ/NX-series Database Connection CPU Units User’s Manual (Cat. No. W527) for the information.
Note: The extended support for databases has ended for the following DB versions.
Please consider replacing the current database with a new version.
| Item | Discription |
|---|---|
| Microsoft Corporation: SQL Server | 2008/2008R2 |
| Oracle Corporation: Oracle Database | 10g |
| Oracle Corporation: MySQL Community Edition | 5.1/5.5 |
| International Business Machines Corporation (IBM): DB2 for Linux, UNIX and Windows | 9.5 |
| Firebird Foundation Incorporated: Firebird | 2.1 |
| The PostgreSQL Global Development Group: PostgreSQL | 9.2/9.3 |
Specifications | PLC – NX102 series
Electrical and Mechanical Specifications
| Item | Specification | |
|---|---|---|
| Model | NX102-[][][][] | |
| Enclosure | Mounted in a panel | |
| Dimensions (mm) *1 | 72 × 100 × 90 mm (W×H×D) | |
| Weight *2 | 390 g max. | |
| Unit power supply |
Power supply voltage | 24 VDC (20.4 to 28.8 VDC) |
| Unit power consumption *3 |
5.80 W max. | |
| Inrush current *4 | For cold start at room temperature: 10 A max./0.1 ms max. and 2.5 A max./150 ms max. |
|
| Current capacity of power supply terminal *5 |
4 A max. | |
| Isolation method | No isolation: between the Unit power supply terminal and internal circuit | |
| Power supply to the NX Unit power supply |
NX Unit power supply capacity |
10 W max. |
| NX Unit power supply efficiency |
80% | |
| Isolation method | No isolation: between the Unit power supply terminal and NX Unit power supply | |
| I/O Power Supply to NX Units | Not provided *6 | |
| External connection terminal |
Communication connector |
RJ45 for EtherNet/IP Communications × 2 RJ45 for EtherCAT Communications × 1 |
| Screwless clamping terminal block |
For Unit power supply input and grounding (Removable) | |
| Output terminal (service supply) |
Not provided | |
| RUN output terminal | Not provided | |
| NX bus connector | 32 NX Units can be connected | |
*1. Includes the End Cover, and does not include projecting parts.
*2. Includes the End Cover. The weight of the End Cover is 82 g.
*3. Includes an SD Memory Card. The NX Unit power consumption to NX Units is not included.
*4. The inrush current that occurs when the supplied power is changed to ON from a continuous OFF state.
The inrush current may vary depending on the operating condition and other conditions. Therefore, select fuses,
breakers, and external power supply devices that have enough margin in characteristic and capacity, considering
thecondition under which the devices are used.
In particular, in case when you insert a switch to turn ON/OFF the DC power supplied from an external power supply, if
the duration of an ON-OFF-ON cycle is one second or less, the inrush control circuit may not function, which cause an
inrush current of approximately 30 A/0.3 ms.
*5. The amount of current that can be passed constantly through the terminal. Do not exceed this current value when you
use a through-wiring for the Unit power supply.
*6. When the type of the I/O power supply to NX Units you use is the supply from NX bus, an Additional I/O Power Supply
Unit is required. Refer to NX-series NX102 CPU Unit Hardware User’s Manual (W593) for details.
General Specifications
| Item | Specification | |
|---|---|---|
| Enclosure | Mounted in a panel | |
| Grounding method | Ground to less than 100 Ω. | |
| Operating environment |
Ambient operating temperature |
0 to 55°C |
| Ambient operating humidity |
10% to 95% (with no condensation) | |
| Atmosphere | Must be free from corrosive gases. | |
| Ambient storage temperature |
-25 to 70°C (excluding battery) | |
| Altitude | 2,000 m max. | |
| Pollution degree | 2 or less: Meets IEC 61010-2-201. | |
| Noise immunity | 2 kV on power supply line (Conforms to IEC 61000-4-4.) | |
| Overvoltage category | Category II: Meets IEC 61010-2-201. | |
| EMC immunity level | Zone B | |
| Vibration resistance | Conforms to IEC 60068-2-6. 5 to 8.4 Hz with 3.5-mm amplitude, 8.4 to 150 Hz, acceleration of 9.8 m/s2 100 min each in X, Y, and Z directions (10 sweeps of 10 min each = 100 min total) |
|
| Shock resistance | Conforms to IEC 60068-2-27. 147 m/s2, 3 times in X, Y, and Z directions |
|
| Battery | Life | 5 years (Power ON time rate 0% (power OFF)) |
| Model | CJ1W-BAT01 (sold separately) | |
| Applicable standards *1 |
EU Directives | EN 61131-2 |
| cULus | Listed UL 61010-2-201 and ANSI/ISA 12.12.01 | |
| Shipbuilding Standards | NK, LR | |
| Other than the above. | RCM, KC, and EAC | |
*1. Refer to the consult your OMRON representative for the most recent applicable standards for each model.
Performance Specifications
| Item | NX102- | ||||||
|---|---|---|---|---|---|---|---|
| 12[][] | 11[][] | 10[][] | 90[][] | ||||
| Processing time |
Instruction execution times |
LD instruction | 3.3 ns | ||||
| Math instructions (for long real data) |
70 ns or more | ||||||
| Programming | Program capacity *1 |
Size | 5 MB | ||||
| Quantity | Number of POU definitions |
3,000 | |||||
| Number of POU instances |
9,000 | ||||||
| Memory capacity for variables *2 |
Retain attribute |
Size | 1.5 MB | ||||
| Number of variables |
10,000 | ||||||
| No Retain attribute |
Size | 32 MB | |||||
| Number of variables |
90,000 | ||||||
| Data types | Number of data types | 1,000 | |||||
| Memory for CJ-series Units (Can be specified with AT specifications for variables.) |
CIO Area | 0 to 6,144 words (CIO 0 to CIO 6,143) *3 |
|||||
| Work Area | 0 to 512 words (W0 to W511) *3 |
||||||
| Holding Area | 0 to 1,536 words (H0 to H1,535) *4 |
||||||
| DM Area | 0 to 32,768 words (D0 to D32,767) *4 |
||||||
| EM Area | 32,768 words × 25 banks (E0_0 to E18_32,767) *4 *5 |
||||||
| Motion control |
Number of controlled axes *6 |
Maximum number of controlled axes |
15 axes | 4 axes | |||
| Motion control axes |
11 axes | — | |||||
| Single-axis position control axes |
4 axes | ||||||
| Maximum number of used real axes |
12 axes | 8 axes | 6 axes | 4 axes | |||
| Used motion control servo axes |
8 axes | 4 axes | 2 axes | — | |||
| Used single- axis position control servo axes |
4 axes | ||||||
| Maximum number of axes for linear interpolation axis control |
4 axes per axes group | — | |||||
| Number of axes for circular interpolation axis control |
2 axes per axes group | — | |||||
| Maximum number of axes groups | 8 axes groups | — | |||||
| Motion control period | The same control period as that is used for the process data communications cycle for EtherCAT. |
||||||
| Cams | Number of cam data points |
Maximum points per cam table |
65,535 points | ||||
| Maximum points for all cam tables |
262,140 points | ||||||
| Maximum number of cam tables |
160 tables | ||||||
| Position units | Pulse, mm, μm, nm, degree, and inch | ||||||
| Override factors | 0.00%, or 0.01% to 500.00% | ||||||
| Built-in EtherNet/IP port |
Number of ports | 2 | |||||
| Physical layer | 10BASE-T/100BASE-TX | ||||||
| Frame length | 1,514 bytes max. | ||||||
| Media access method | CSMA/CD | ||||||
| Modulation | Baseband | ||||||
| Topology | Star | ||||||
| Baud rate | 100 Mbps (100BASE-TX) | ||||||
| Transmission media | STP (shielded, twisted-pair) cable of Ethernet category 5, 5e or higher |
||||||
| Maximum transmission distance between Ethernet switch and node |
100 m | ||||||
| Maximum number of cascade connections | There are no restrictions if an Ethernet switch is used. | ||||||
| CIP service: Tag data links (cyclic com- munications) |
Maximum number of connections |
32 per port 64 total |
|||||
| Packet interval *7 | Can be set for each connection. 1 to 10,000 ms in 1-ms increments |
||||||
| Permissible communications band |
12,000 pps *8 *9 (including heartbeat, CIP Safety routing) |
||||||
| Maximum number of tag sets | 32 per port 40 total *10 |
||||||
| Tag types | Network variables CIO/WR/HR/DM |
||||||
| Number of tags per connection (i.e., per tag set) |
8 (7 tags if Controller status is included in the tag set.) | ||||||
| Maximum number of tags | 256 per port 512 total |
||||||
| Maximum link data size per node (total size for all tags) |
19,200 bytes per port 38,400 bytes total |
||||||
| Maximum data size per connection |
600 bytes | ||||||
| Maximum number of registrable tag sets |
32 per port 40 total *10 (1 connection = 1 tag set) |
||||||
| Maximum tag set size | 600 bytes (Two bytes are used if Controller status is included in the tag set.) |
||||||
| Multi-cast packet filter *11 | Supported. | ||||||
| CIP message service: Explicit messages |
Class 3 (number of connections) |
32 per port 64 total (clients plus server) |
|||||
| UCMM (non- connection type) |
Maximum number of clients that can communicate at one time |
32 per port 64 total |
|||||
| Maximum number of servers that can communicate at one time |
32 per port 64 total |
||||||
| CIP Safety routing |
Maximum number of routable CIP Safety connections |
16 total | |||||
| Maximum routable safety data length per connection |
32 bytes | ||||||
| Number of TCP sockets | 60 | ||||||
| OPC UA Server |
Support profile/Model | UA 1.02 Micro Embedded Device Server Profile PLCOpen Information Model |
|||||
| Default Endpoint/Port | opc.tcp://192.168.250.1:4840/ | ||||||
| Maximum number of sessions (Client) |
5 | ||||||
| Maximum number of Monitored Items per server |
2,000 | ||||||
| Sampling rate of Monitored Items (ms) |
0, 50, 100, 250, 500, 1000, 2000, 5,000, 10,000 (If set to 0 (zero), it is assumed that is set to 50.) |
||||||
| Maximum number of Subscriptions per server |
100 | ||||||
| Maximum number of variables that can be published |
10,000 | ||||||
| Maximum number of value attributes that can be published *16 |
10,000 | ||||||
| Maximum number of structure definitions that can be published |
100 | ||||||
| Restrictions on variables unable to be published |
• Variables whose size is over 1,024 bytes • Two-dimensional or higher structure arrays • Structures that include two-dimensional and higher arrays • Structures with four or higher levels of nesting • Unions • Arrays whose index number suffix does no start from 0 • Arrays with 1,024 or more elements • Structures with 100 or more members |
||||||
| SecurityPolicy/Mode | Select one of the following. None Sign – Basic128Rsa15 Sign – Basic256 Sign – Basic256Sha256 SignAndEncrypt – Basic128Rsa15 SignAndEncrypt – Basic256 SignAndEncrypt – Basic256Sha256 |
||||||
| Application Authentica- tion |
Authentication | X.509 | |||||
| Maximum number of storable certifications |
Trusted certification: 32 Issuer certification: 32 Rejected certification: 32 |
||||||
| User Authentica- tion |
Authentication | You can set the following items. User name/password Anonymous |
|||||
| Built-in EtherCAT port |
Communications standard | IEC 61158 Type12 | |||||
| EtherCAT master specifications | Class B (Feature Pack Motion Control compliant) | ||||||
| Physical layer | 100BASE-TX | ||||||
| Modulation | Baseband | ||||||
| Baud rate | 100 Mbps (100BASE-TX) | ||||||
| Duplex mode | Auto | ||||||
| Topology | Line, daisy chain, branching and ring *13 | ||||||
| Transmission media | Twisted-pair cable of category 5 or higher (double- shielded straight cable with aluminum tape and braiding) |
||||||
| Maximum transmission distance between nodes |
100 m | ||||||
| Maximum number of slaves | 64 | ||||||
| Range of node addresses that can be set | 1 to 192 | ||||||
| Maximum process data size | Input: 5,736 bytes Output: 5,736 bytes *14 |
||||||
| Maximum process data size per slave | Input: 1,434 bytes Output: 1,434 bytes |
||||||
| Communications cycle | 1,000 to 32,000 μs (in 250-μs increments) | ||||||
| Sync jitter | 1 μs max. | ||||||
| Unit configuration |
Units on CPU Rack |
Maximum number of NX Units that can be mounted to the CPU Unit |
32 | ||||
| Maximum I/O data size that can be allocated in the CPU Unit |
Inputs: 8,192 bytes *15 Outputs: 8,192 bytes *15 |
||||||
| Maximum number of NX Units for entire controller |
400 | ||||||
| Power supply | Model | A non-isolated power supply for DC input is built into the CPU Unit. |
|||||
| Power OFF detection time | 2 to 8 ms | ||||||
| Internal clock |
Accuracy | At ambient temperature of 55°C: -3.5 to 0.5 min error per month At ambient temperature of 25°C: -1.5 to 1.5 min error per month At ambient temperature of 0°C: -3 to 1 min error per month |
|||||
| Retention time of built-in capacitor | At ambient temperature of 40°C: 10 days | ||||||
*1. Execution objects and variable tables (including variable names)
*2. Memory used for CJ-series Units is included.
*3. The value can be set in 1-word increments. The value is included in the total size of variables without a Retain
attribute.
*4. The value can be set in 1-word increments. The value is included in the total size of variables with a Retain attribute.
*5. It is not possible to use the maximum number of words simultaneously for all banks, because the memory capacity for
variables with a Retain attribute is limited to 1.5 MB.
*6. For terminology, refer to the NJ/NX-series CPU Unit Motion Control User’s Manual (Cat. No. W507).
*7. Data will be refreshed at the set interval, regardless of the number of nodes.
*8. “pps” means packets per second, i.e., the number of communications packets that can be sent or received in one
second.
*9. The allowable bandwidth varies depending on the RPI of the connection in use, the primary task period, and the
number of ports simultaneously used for EtherNet/IP communications.
*10.When tag sets that exceed the total of 40 are set, a Number of Tag Sets for Tag Data Links Exceeded (840E0000 hex)
occurs.
*11.As the EtherNet/IP port implements the IGMP client, unnecessary multi-cast packets can be filtered by using an
Ethernet switch that supports IGMP Snooping.
*12.The number of value attributes is defined by the following formula.
Number of value attributes = (Number of basic data type variables) + (Number of array-specified elements) + (Number
of values in the structure)
*13.Ring topology is supported with the project version 1.40 or later of NX102-[][]00.
Slaves on a ring topology should support a ring topology. If Omron slaves, please see the user’s manual of slaves.
*14.For project unit version earlier than 1.40, the data must be within four frames.
*15.You can check the I/O allocation status with the Sysmac Studio. Refer to the NJ/NX-series CPU Unit Software User’s
Manual (Cat. No. W501) for how to check the I/O allocation status. Also, refer to the relevant manuals for specific
Units for the maximum I/O data size per NX Unit.
Function Specifications
| Item | NX102 | |||
|---|---|---|---|---|
| Tasks | Function | I/O refreshing and the user program are executed in units that are called tasks. Tasks are used to specify execution conditions and execution priority. |
||
| Periodically executed tasks |
Maximum number of primary periodic tasks |
1 | ||
| Maximum number of periodic tasks |
2 | |||
| Conditionally executed tasks |
Maximum number of event tasks |
32 | ||
| Execution condition | When Activate Event Task instruction is executed or when condition expression for variable is met |
|||
| Programming | POU (Program Organization Unit) |
Programs | POUs that are assigned to tasks | |
| Function blocks | POUs that are used to create objects with specific conditions |
|||
| Functions | POUs that are used to create objects that determine unique outputs for the inputs, such as for data processing |
|||
| Programming languages |
Types | Ladder diagrams *1 and structured text (ST) | ||
| Namespaces | A concept that is used to group identifiers for POU definitions |
|||
| Variables | External access of variables |
Network variables | The function which allows access from the HMI, host computers, or other controllers |
|
| Data types | Basic data types |
Boolean | BOOL | |
| Bit strings | BYTE, WORD, DWORD, LWORD | |||
| Integers | INT, SINT, DINT, LINT, UINT, USINT, UDINT, ULINT |
|||
| Real numbers | REAL, LREAL | |||
| Durations | TIME | |||
| Dates | DATE | |||
| Times of day | TIME_OF_DAY | |||
| Date and time | DATE_AND_TIME | |||
| Text strings | STRING | |||
| Derivative data types | Structures, unions, enumerations | |||
| Structures | Function | A derivative data type that groups together data with different variable types |
||
| Maximum number of members |
2,048 | |||
| Nesting maximum levels |
8 | |||
| Member data types | Basic data types, structures, unions, enumerations, array variables |
|||
| Specifying member offsets |
You can use member offsets to place structure members at any memory locations |
|||
| Unions | Function | A derivative data type that enables access to the same data with different data types |
||
| Maximum number of members |
4 | |||
| Member data types | BOOL, BYTE, WORD, DWORD, LWORD | |||
| Enumerations | Function | A derivative data type that uses text strings called enumerators to express variable values |
||
| Data type attributes |
Array specifications |
Function | An array is a group of elements with the same data type. You specify the number (subscript) of the element from the first element to specify the element |
|
| Maximum number of dimensions |
3 | |||
| Maximum number of elements |
65,535 | |||
| Array specifications for FB instances |
Supported | |||
| Range specifications | You can specify a range for a data type in advance. The data type can take only values that are in the specified range |
|||
| Libraries | User libraries | |||
| Motion control |
Control modes | Position control, velocity control, torque control |
||
| Axis types | Servo axes, virtual servo axes, encoder axes, virtual encoder axes, PTP axes |
|||
| Positions that can be managed | Command positions and actual positions | |||
| Single axes | Single-axis position control |
Absolute positioning | Positioning is performed for a target position that is specified with an absolute value |
|
| Relative positioning | Positioning is performed for a specified travel distance from the command current position |
|||
| Interrupt feeding | Positioning is performed for a specified travel distance from the position where an interrupt input was received from an external input |
|||
| Cyclic synchronous absolute positioning |
A positioning command is output each control period in Position Control Mode |
|||
| Single-axis velocity control |
Velocity control | Velocity control is performed in Position Control Mode |
||
| Cyclic synchronous velocity control |
A velocity command is output each control period in Velocity Control Mode |
|||
| Single-axis torque control |
Torque control | The torque of the motor is controlled | ||
| Single-axis synchronized control |
Starting cam operation |
A cam motion is performed using the specified cam table |
||
| Ending cam operation |
The cam motion for the axis that is specified with the input parameter is ended |
|||
| Starting gear operation |
A gear motion with the specified gear ratio is performed between a master axis and slave axis |
|||
| Positioning gear operation |
A gear motion with the specified gear ratio and sync position is performed between a master axis and slave axis |
|||
| Ending gear operation | The specified gear motion or positioning gear motion is ended |
|||
| Synchronous positioning |
Positioning is performed in sync with a specified master axis |
|||
| Master axis phase shift |
The phase of a master axis in synchronized control is shifted |
|||
| Combining axes | The command positions of two axes are added or subtracted and the result is output as the command position |
|||
| Single-axis manual operation |
Powering the Servo | The Servo in the Servo Drive is turned ON to enable axis motion |
||
| Jogging | An axis is jogged at a specified target velocity |
|||
| Auxiliary functions for single-axis control |
Resetting axis errors |
Axes errors are cleared | ||
| Homing | A motor is operated and the limit signals, home proximity signal, and home signal are used to define home |
|||
| Homing with parameter |
The parameters are specified, the motor is operated, and the limit signals, home proximity signal, and home signal are used to define home |
|||
| High-speed homing | Positioning is performed for an absolute target position of 0 to return to home |
|||
| Stopping | An axis is decelerated to a stop | |||
| Immediately stopping | An axis is stopped immediately | |||
| Setting override factors |
The target velocity of an axis can be changed | |||
| Changing the current position |
The command current position or actual current position of an axis can be changed to any position. |
|||
| Enabling external latches |
The position of an axis is recorded when a trigger occurs |
|||
| Disabling external latches |
The current latch is disabled | |||
| Zone monitoring | You can monitor the command position or actual position of an axis to see when it is within a specified range (zone) |
|||
| Enabling digital cam switches |
You can turn a digital output ON and OFF according to the position of an axis |
|||
| Monitoring axis following error |
You can monitor whether the difference between the command positions or actual positions of two specified axes exceeds a threshold value |
|||
| Resetting the following error |
The error between the command current position and actual current position is set to 0 |
|||
| Torque limit | The torque control function of the Servo Drive can be enabled or disabled and the torque limits can be set to control the output torque |
|||
| Command position compensation |
The function which compensates the position for the axis in operation |
|||
| Cam monitor | Outputs the specified offset position for the slave axis in synchronous control. |
|||
| Start velocity | You can set the initial velocity when axis motion starts |
|||
| Axes groups | Multi-axes coordinated control |
Absolute linear interpolation |
Linear interpolation is performed to a specified absolute position |
|
| Relative linear interpolation |
Linear interpolation is performed to a specified relative position |
|||
| Circular 2D interpolation |
Circular interpolation is performed for two axes |
|||
| Axes group cyclic synchronous absolute positioning |
A positioning command is output each control period in Position Control Mode |
|||
| Auxiliary functions for multi-axes coordinated control |
Resetting axes group errors |
Axes group errors and axis errors are cleared |
||
| Enabling axes groups | Motion of an axes group is enabled | |||
| Disabling axes groups |
Motion of an axes group is disabled | |||
| Stopping axes groups |
All axes in interpolated motion are decelerated to a stop |
|||
| Immediately stopping axes groups |
All axes in interpolated motion are stopped immediately |
|||
| Setting axes group override factors |
The blended target velocity is changed during interpolated motion |
|||
| Reading axes group positions |
The command current positions and actual current positions of an axes group can be read |
|||
| Changing the axes in an axes group |
The Composition Axes parameter in the axes group parameters can be overwritten temporarily |
|||
| Common items |
Cams | Setting cam table properties |
The end point index of the cam table that is specified in the input parameter is changed |
|
| Saving cam tables | The cam table that is specified with the input parameter is saved in non-volatile memory in the CPU Unit |
|||
| Generating cam tables |
The cam table is generated from the cam property and cam node that is specified in input parameters |
|||
| Parameters | Writing MC settings | Some of the axis parameters or axes group parameters are overwritten temporarily |
||
| Changing axis parameters |
The axis parameters can be accessed or changed from the user program |
|||
| Auxiliary functions |
Count modes | You can select either Linear Mode (finite length) or Rotary Mode (infinite length). |
||
| Unit conversions | You can set the display unit for each axis according to the machine |
|||
| Acceleration/ deceleration control |
Automatic acceleration/ deceleration control |
Jerk is set for the acceleration/deceleration curve for an axis motion or axes group motion |
||
| Changing the acceleration and deceleration rates |
You can change the acceleration or deceleration rate even during acceleration or deceleration |
|||
| In-position check | You can set an in-position range and in- position check time to confirm when positioning is completed |
|||
| Stop method | You can set the stop method to the immediate stop input signal or limit input signal |
|||
| Re-execution of motion control instructions |
You can change the input variables for a motion control instruction during execution and execute the instruction again to change the target values during operation |
|||
| Multi-execution of motion control instructions (Buffer Mode) |
You can specify when to start execution and how to connect the velocities between operations when another motion control instruction is executed during operation |
|||
| Continuous axes group motions (Transition Mode) |
You can specify the Transition Mode for multi-execution of instructions for axes group operation |
|||
| Monitoring functions |
Software limits | The movement range of an axis is monitored | ||
| Following error | The error between the command current value and the actual current value is monitored for each axis |
|||
| Velocity, acceleration rate, deceleration rate, torque, interpolation velocity, interpolation acceleration rate, interpolation deceleration rate |
You can set and monitor warning values for each axis and each axes group |
|||
| Absolute encoder support | You can use an OMRON 1S-series Servomotor or G5-series Servomotor with an Absolute Encoder to eliminate the need to perform homing at startup |
|||
| Input signal logic inversion | You can inverse the logic of immediate stop input signal, positive limit input signal, negative limit input signal, or home proximity input signal |
|||
| External interface signals | The Servo Drive input signals listed below are used. Home signal, home proximity signal, positive limit signal, negative limit signal, immediate stop signal, interrupt input signal |
|||
| Unit (I/O) management |
EtherCAT slaves |
Maximum number of slaves | 64 | |
| Communi- cations |
Built-in EtherNet/IP port |
Communications protocol | TCP/IP, UDP/IP | |
| TCP/IP functions |
CIDR | The function which performs IP address allocations without using a class (class A to C) of IP address |
||
| IP Forwarding | The function which forwards IP packets between interfaces |
|||
| Packet Filter | The function which checks the IP packet to determine whether to receive and send it based on the source IP address and TCP port number |
|||
| CIP communica- tions service |
Tag data links | Programless cyclic data exchange is performed with the devices on the EtherNet/IP network |
||
| Message communications |
CIP commands are sent to or received from the devices on the EtherNet/IP network |
|||
| CIP Safety routing | Routing function for CIP Safety on the EtherNet/IP network. The endpoint of CIP Safety is NX-SL5[]00 in the system |
|||
| TCP/IP applications |
Socket services | Data is sent to and received from any node on Ethernet using the UDP or TCP protocol. Socket communications instructions are used |
||
| FTP client | Files are transferred via FTP from the CPU Unit to computers or controllers at other Ethernet nodes. FTP client communications instructions are used |
|||
| FTP server | Files can be read from or written to the SD Memory Card in the CPU Unit from computers at other Ethernet nodes |
|||
| Automatic clock adjustment |
Clock information is read from the NTP server at the specified time or at a specified interval after the power supply to the CPU Unit is turned ON. The internal clock time in the CPU Unit is updated with the read time |
|||
| SNMP agent | Built-in EtherNet/IP port internal status information is provided to network management software that uses an SNMP manager |
|||
| OPC UA | Server function | The function to respond to requests from clients on the OPC UA network |
||
| EtherCAT port |
Supported services |
Process data communications |
A communications method to exchange control information in cyclic communications between the EtherCAT master and slaves. This communications method is defined by CoE |
|
| SDO communications |
A communications method to exchange control information in noncyclic event communications between EtherCAT master and slaves. This communications method is defined by CoE |
|||
| Network scanning | Information is read from connected slave devices and the slave configuration is automatically generated |
|||
| DC (Distributed Clock) | Time is synchronized by sharing the EtherCAT system time among all EtherCAT devices (including the master) |
|||
| Enable/disable settings for slaves | The slaves can be enabled or disabled as communications targets |
|||
| Disconnecting/connecting slaves | Temporarily disconnects a slave from the EtherCAT network for maintenance, such as for replacement of the slave, and then connects the slave again |
|||
| Supported application protocol |
CoE | SDO messages of the CAN application can be sent to slaves via EtherCAT |
||
| Communications instructions | CIP communications instructions, socket communications instructions, SDO message instructions, no-protocol communications instructions, FTP client instructions, Modbus RTU protcol instructions, Modbus TCP protcol instructions |
|||
| System management |
Event logs | Function | Events are recorded in the logs | |
| Maximum number of events |
System event log | 768 *2 [containing] • For CPU Unit: 512 • For NX Unit without MPU: 256 |
||
| Access event log | 576 [containing] • For CPU Unit: 512 • For NX Unit without MPU: 64 |
|||
| User-defined event log |
512 | |||
| Debugging | Online editing |
Single | Programs, function blocks, functions, and global variables can be changed online. More than one operators can change POUs individually via network |
|
| Forced refreshing | The user can force specific variables to TRUE or FALSE |
|||
| Maximum number of forced variables |
Device variables for EtherCAT slaves |
64 | ||
| MC Test Run | Motor operation and wiring can be checked from the Sysmac Studio |
|||
| Synchronizing | The project file in the Sysmac Studio and the data in the CPU Unit can be made the same when online |
|||
| Differential monitoring | You can monitor when a variable changes to TRUE or changes to FALSE |
|||
| Maximum number of monitored variables |
8 | |||
| Data tracing | Types | Single triggered trace |
When the trigger condition is met, the specified number of samples are taken and then tracing stops automatically |
|
| Continuous trace | Data tracing is executed continuously and the trace data is collected by the Sysmac Studio |
|||
| Maximum number of simultaneous data traces |
2 | |||
| Maximum number of records | 10,000 | |||
| Sampling | Maximum number of sampled variables |
48 | ||
| Timing of sampling | Sampling is performed for the specified task period, at the specified time, or when a sampling instruction is executed |
|||
| Triggered traces | Trigger conditions are set to record data before and after an event |
|||
| Trigger conditions | • When BOOL variable changes to TRUE or FALSE • Comparison of non-BOOL variable with a constant. Comparison method: Equals (=), Greater than (>), Greater than or equals (≥), Less than (<), Less than or equals (≤), Not equal (≠) |
|||
| Delay | You can set the percentage of sampling before and after the trigger condition is met |
|||
| Safety data logging |
Function | Records variables used in the safety program of the Safety CPU Unit in a chronological order |
||
| Targets | Target Safety CPU Unit |
NX-SL5[]00 *3 | ||
| Target variable types | Exposed variables and device variables used in the safety program |
|||
| Maximum number of logged variables |
100 | |||
| Data types | SAFEBOOL, SAFEBYTE, SAFEWORD, SAFEINT, SAFEDINT,BOOL, BYTE, WORD, INT, DINT |
|||
| Maximum logging time |
480 s (Depends on logging interval) | |||
| Logging interval | Select from minimum value which stores from primary periodic task cycle or adds constant number multiple (x1, x2, x3, x4) of primary periodic task cycle *4 |
|||
| Maximum number of simultaneous executions |
2 | |||
| Simulation | The operation of the CPU Unit is emulated in the Sysmac Studio |
|||
| Reliability functions |
Self- diagnosis |
Controller errors |
Levels | Major faults, partial faults, minor faults, observation, information |
| User-defined errors | User-defined errors are registered in advance and then records are created by executing instructions |
|||
| Levels | 8 | |||
| Security | Protecting software assets and preventing operating mistakes |
CPU Unit names and serial IDs | When going online to a CPU Unit from the Sysmac Studio, the CPU Unit name in the project is compared to the name of the CPU Unit being connected to |
|
| Protection | User program transfer with no restoration information |
You can prevent reading data in the CPU Unit from the Sysmac Studio |
||
| CPU Unit write protection |
You can prevent writing data to the CPU Unit from the Sysmac Studio or SD Memory Card |
|||
| Overall project file protection |
You can use passwords to protect .smc files from unauthorized opening on the Sysmac Studio |
|||
| Data protection | You can use passwords to protect POUs on the Sysmac Studio |
|||
| Verification of operation authority | Online operations can be restricted by operation rights to prevent damage to equipment or injuries that may be caused by operating mistakes |
|||
| Number of groups | 5 | |||
| Verification of user program execution ID |
The user program cannot be executed without entering a user program execution ID from the Sysmac Studio for the specific hardware (CPU Unit) |
|||
| SD Memory Card functions |
Storage type | SD Memory Card, SDHC Memory Card | ||
| Application | Automatic transfer from SD Memory Card |
When the power supply to the controller is turned ON, the data that is stored in the autoload directory of the SD Memory Card is transferred to the controller |
||
| Program transfer from SD Memory Card |
With the specification of the system-defined variable, you can transfer a program that is stored in the SD Memory Card to the controller |
|||
| SD Memory Card operation instructions |
You can access SD Memory Cards from instructions in the user program |
|||
| File operations from the Sysmac Studio |
You can perform file operations for controller files in the SD Memory Card and read/write standard document files on the computer |
|||
| SD Memory Card life expiration detection |
Notification of the expiration of the life of the SD Memory Card is provided in a system- defined variable and event log |
|||
| Backing up data |
SD Memory Card backups |
Operating methods |
CPU Unit front- panel DIP switch |
You can perform backup, verification, and restoration operations by manipulating the front-panel DIP switch on the CPU Unit |
| Specification with system-defined variables |
You can perform backup, verification, and restoration operations by manipulating system-defined variables |
|||
| SD Memory Card Window in Sysmac Studio |
Backup and verification operations are performed from the SD Memory Card Window of the Sysmac Studio |
|||
| Special instruction | The special instruction is used to backup data |
|||
| Protection | Disabling backups to SD Memory Cards |
Backing up data to a SD Memory Card is prohibited |
||
| Safety Unit Restore from SD Memory Card | Restores the data of the Safety CPU Unit using the front-panel DIP switch on the Safety CPU Unit and SD Memory Card |
|||
| Sysmac Studio Controller backups | The Sysmac Studio is used to backup, restore, or verify controller data |
|||
*1. Inline ST is supported. (Inline ST is ST that is written as an element in a ladder diagram.)
*2. Up to 512 system logs for events in the CPU Unit and 256 system logs in the NX Unit can be recorded.
*3. When connected to a CPU rack.
*4. Minimum value fulfills all these conditions.
• Larger than 5 ms
• Constant number multiple of primary periodic task cycle
Function Specifications of the Database Connection CPU Units
Besides functions of the NX102-[][][][], functions supported by the NX102-[][]20 are as follows.
| Item | Description | |||||
|---|---|---|---|---|---|---|
| NX102-1220 | NX102-1120 | NX102-1020 | NX102-9020 | |||
| Supported port | Built-in EtherNet/IP port | |||||
| Supported DB versions *1 *2 |
SQL Server by Microsoft | 2012/2014/2016/2017 | ||||
| Oracle Database by Oracle | 11g/12c/18c | |||||
| DB2 for Linux, UNIX and Windows by IBM |
9.7/10.1/10.5/11.1 | |||||
| MySQL Community Edition by Oracle*3 |
5.6/5.7/8.0 | |||||
| Firebird by Firebird Foundation |
2.5 | |||||
| PostgreSQL by PostgreSQL Global Development Group |
9.4/9.5/9.6/10 | |||||
| Number of DB Connections (Number of databases that can be connected at the same time) |
2*4 *5 | |||||
| Instruction | Supported operations | The following operations can be performed by executing DB Connection Instructions in the CPU Units: Inserting records (INSERT), Updating records (UPDATE), Retrieving records (SELECT), Deleting records (DELETE), Execute Stored Procedure*6, and Execute Batch Insert*6 |
||||
| Max. number of instructions for simultaneous execution |
32 | |||||
| Max. number of columns in an INSERT operation |
SQL Server: 1,024 Oracle: 1,000 DB2: 1,000 MySQL: 1,000 Firebird: 1,000 PostgreSQL: 1,000 |
|||||
| Max. number of columns in an UPDATE operation |
SQL Server: 1,024 Oracle: 1,000 DB2: 1,000 MySQL: 1,000 Firebird: 1,000 PostgreSQL: 1,000 |
|||||
| Max. number of columns in a SELECT operation |
SQL Server: 1,024 Oracle: 1,000 DB2: 1,000 MySQL: 1,000 Firebird: 1,000 PostgreSQL: 1,000 |
|||||
| Max. number of records in the output of a SELECT operation |
65,535 elements, 4 MB | |||||
| Stored procedure call *6 |
Supported databases |
• SQL Server • Oracle Database • MySQL Community Edition • PostgreSQL |
||||
| Argument (Sum of IN, OUT and INOUT) |
Up to 256 variables*7 | |||||
| Return value | One variable | |||||
| Result set | Supported | |||||
| Spool function | Not supported | |||||
| Batch insert execution *6 |
Supported databases |
• SQL Server • Oracle Database • MySQL Community Edition • PostgreSQL |
||||
| Supported data size |
Less than 1,000 columns and upper limit (8 MB) of structure variable size or less*8 |
|||||
| Spool function | Not supported | |||||
| Max. number of DB Map Variables for which a mapping can be connected *9 |
SQL Server: 30*10 Oracle: 20*10 DB2: 20*10 MySQL: 20*10 Firebird: 15 PostgreSQL: 20*10 |
|||||
| Run mode of the DB Connection Service | Operation Mode or Test Mode • Operation Mode: When each instruction is executed, the service actually accesses the DB • Test Mode: When each instruction is executed, the service ends the instruction normally without accessing the DB actually |
|||||
| Spool function | Used to store SQL statements when an error occurred and resend the statements when the communications are recovered from the error |
|||||
| Spool capacity*11 | 192 KB | |||||
| Operation Log function | The following three types of logs can be recorded: • Execution Log: Log for tracing the executions of the DB Connection Service • Debug Log: Detailed log for SQL statement executions of the DB Connection Service • SQL Execution Failure Log: Log for execution failures of SQL statements in the DB |
|||||
| DB Connection Service Shutdown function |
Used to shut down the DB Connection Service after automatically saving the operation log files into the SD Memory Card |
|||||
| Encrypted Communi- cation |
Supported databases | • SQL Server • Oracle Database • MySQL Community Edition • PostgreSQL |
||||
| TLS Ver. | TLS 1.2 | |||||
*1. SQL Server 2014, Oracle Database 12c and PostgreSQL 9.4 are supported by the DB Connection Service Version 1.02
or higher.
SQL Server 2016, MySQL 5.7, DB2 11.1 and PostgreSQL 9.5/9.6 are supported by the DB Connection Service Version
1.03 or higher.
SQL Server 2017 is supported by the DB Connection Service Version 1.04 or higher.
Oracle Database 18c, MySQL Community Edition 8.0 and PostgreSQL 10 are supported by the DB Connection Service
Version 2.00 or higher.
You cannot use Oracle 10g with the DB Connection Service version 2.00 or higher.
*2. Connection to the DB on the cloud is not supported.
*3. The supported storage engines of the DB are InnoDB and MyISAM.
*4. When two or more DB Connections are established, the operation cannot be guaranteed if you set different database
types for the connections.
*5. For the DB Connection Service Version lower than 1.04, Number of DB Connection is 1.
*6. The function is available for the DB Connection Service Version 2.00 or higher.
*7. Depends on members of a structure.
*8. Constrained by the memory capacity for variables. See the specifications for the memory capacity for variables.
*9. Even if the number of DB Map Variables has not reached the upper limit, the maximum total number of members of
structures used as data type of DB Map Variables is 10,000.
*10.For DB Connection Service Version lower than 1.04, Max. number of DB Map Variables for which a mapping can be
connected is 15.
*11.Refer to the NJ/NX-series Database Connection CPU Units User’s Manual (Cat. No. W527) for the information.
Note: The extended support for databases has ended for the following DB versions.
Please consider replacing the current database with a new version.
| Item | Discription |
|---|---|
| Microsoft Corporation: SQL Server | 2008/2008R2 |
| Oracle Corporation: Oracle Database | 10g |
| Oracle Corporation: MySQL Community Edition | 5.1/5.5 |
| International Business Machines Corporation (IBM): DB2 for Linux, UNIX and Windows | 9.5 |
| Firebird Foundation Incorporated: Firebird | 2.1 |
| The PostgreSQL Global Development Group: PostgreSQL | 9.2/9.3 |
Dimensions | PLC – NX102 series
NX-Series NX102 CPU Unit
NX102-[][][][]
![NX102-[][][][] Dimensions 2](https://www.pneu-hyd.co.th/images/Products/omron/automation/plc/nx102/dimensions/3705_dm_126-282839.gif)
*1. The dimension from the attachment surface of the DIN Track to the front surface of the CPU Unit.
*2. The dimension from the terminal block lock lever to the back surface of the CPU Unit.
For dimensions after attaching the communications cables, refer to NX-series NX102 CPU Unit Hardware User’s Manual (W593).
End cover
NX-END02
![NX102-[][][][] Dimensions 4](https://www.pneu-hyd.co.th/images/Products/omron/automation/plc/nx102/dimensions/3705_dm_226-282840.gif)
*1. The dimension from the attachment surface of the DIN Track to the front surface of the end cover.
Features | PLC – NX102 series
The NX1 can utilize information, take safety measures, and control quality while at the same time improving production efficiency through high-speed, high-precision control.This contributes to continuous improvement in productivity.
- Real-time traceability
- Integrated safety across production line
- High-speed in-line inspection
- NX1 brings advanced control in miniaturized size
- High-speed, high-precision control
- Redundancy to minimize downtime (NX102-[][]00
- Enhanced Ethernet functionality
Properties | PLC – NX102 series
| PLC | NX1P2 |
|---|---|
| Power supply voltage | 24 VDC |
| Communication connector | RJ45 for EtherNet/IP Communications × 2 |
| RJ45 for EtherCAT Communications × 1 | |
| Program capacitysize | 5 MB |
| Maximum number of controlled axes | 15 / 4axes |
| INput | Point |
| Output | Point |
| Externalconnectionterminals: NX bus connector | 32 Unit |
| Program | Ladder diagrams, structured text (ST) และ POUs |
| Weight | 390 g |
| dimensions (W x L x H) mm | 100 x 72 x 90 |
ติดต่อแผนก Automation & Robots
